642 Electrical Design Engineer jobs in Albuquerque,NM

New, Posted 1 day ago

Apply Directly

Sr. Project Engineer

MasTec Industrial

Albuquerque, NM 87101

$130,000-$160,000/yr

Apply Directly

Electronics Engineer III

National Radio Astronomy Observatory

Albuquerque, NM 87101

HybridHealth InsurancePaid Time OffRetirement Benefit

Bachelor of Science in Electrical Engineering, Applied Physics, or a closely related field.
The starting salary/hourly rate of this position is between $99,822-$120,837.
Observatory employees must be authorized to work in the United States.
The Observatory presently cannot sponsor H-1B Visas for this position.
Post-offer, pre-employment/pre-placement drug screen must be successfully passed.
May occasionally be required to work outdoors or climb on antenna to heights greater than 40 feet above the ground.
May be required to travel domestically and internationally by air carrier and to travel by car between NRAO sites.
Experience in design, manufacture, and/or maintenance and repair of receiver systems, microwave antennas and feeds, local oscillators, and microwave/RF mixers and filters (minimum of three years).
Use of various types of electronics test equipment and familiarity with automated test setups to support general test and measurement.

SmartExplore AI is experimental.

Apply Directly

Sr. Power Electronics Engineer

Raytheon

Albuquerque, NM 87121

OnsiteFlexible ScheduleHealth InsurancePaid Time OffRetirement Benefit

Active and transferable U.S. government issued security clearance is required prior to start date
U.S. citizenship is required, as only U.S. citizens are eligible for a security clearance
Security Clearance Type: DoD Clearance: Secret
Ability to obtain INTERIM U.S. government issued security clearance is required prior to start date
Typically requires a degree in Science, Technology, Engineering or Mathematics (STEM) and a minimum of 5 years of prior relevant experience or an Advanced Degree in a related field and minimum 3 years experience
Experience with any of the following: Power, analog, digital, and / or mixed signal circuit design or analysis and / or digital signal processing
Experience with analog laboratory equipment such as waveform generators, oscilloscopes, spectrum analyzers, and/or network analyzers
Experience with simulation software for circuit analysis or modeling
Experience leading Root-Cause Corrective Action investigations
Experience leading electrical engineering design
Experience with any of the following tools: Mentor Graphics Designer, PSPICE, System Vision, MATLAB, Mathcad, IDL, Computer Simulation Technologies (CST), Microwave Design Studio, High Frequency Structure Simulator (HFSS), Advanced Design System (ADS), SABER RD, SIMPLIS, or xDX Designer
Design and/or Analysis experience with analog electronics design, including at least one of the following: Power supply topologies (buck, boost, buck-boost), FETs/BJTs, op-amp, high/low/band pass filters, clock/data termination, and comparator circuits
Experience with subsystems integration and test, problem investigation, Statistical Process Control (SPC) methods in achieving production yield improvements, technical writing, formal presentation, and implementing Engineering Change Notices
Experience leading or executing Electronics CAD layouts for printed wiring or circuit boards
Self-starter who's capable of working independently as well as with a small technical team. Providing technical oversight and direction, cost estimation, tracking & reporting, coordination, preparation of detailed technical team reports, and proposal support
Demonstrated ability to lead teams to achieve schedule, budget and technical commitments
Experience with project management tools such as Earned Value and/or Agile Execution
Proposal development experience

SmartExplore AI is experimental.

Measurement Engineer - Gas Utilities (I/II/III)

TECO Energy

Albuquerque, NM 87101

No Experience

New, Posted 1 day ago

Watch Netflix (Tagger): $12-$46

Netflix

Albuquerque, NM 87101

New, Posted 1 day ago

Apply Directly

Elevator Technician

TK Elevator Corporation

Albuquerque, NM 87113

Onsite

High school diploma or GED
2+ years related work experience as a mechanic or technician in a commercial setting
Ability to lift up to 100 pounds on a regular basis
Self-starter and work independently with little supervision
Monitors and analyzes the function of mechanical and electrical components as necessary to troubleshoot, adjust or repair the equipment
Preforms preventative maintenance task including visually inspecting, manually cleaning and lubrication elevator systems and components in a controlled or non-controlled climate field setting

SmartExplore AI is experimental.

Apply Directly

Nuclear Engineer

US Navy

Los Ranchos de Albuquerque, NM 87114

New, Posted 1 day ago

ResumeLibrary

Field Service Engineer II

EV Group

Rio Rancho, NM 87124

Operations & Maintenance BESS Technician

GridWorks

Albuquerque, NM 87101

New, Posted 8 hours ago

Easy Apply

Maintenance I

Target Hospitality

Albuquerque, NM

Onsite

0-1 year as a facilities maintenance worker or equivalent
Ability to read and write in English
Ability to hear and understand verbal instruction as well as other sounds such as safety alarms/ signals
Ability to communicate effectively; written and orally in English
Must be able to see without impairment for inspection purposes and ability to read small text such as product warning labels
Exposure to extreme hot and cold environments
May be exposed periodically to elevated noise and surroundings
Must be able to pass a background check and urine analysis
Must provide your own transportation to and from the facility
Work within a team environment
Must be able to work effectively and efficiently with or without supervision
Strong prioritization and time management skills
Occupational Safety and Health Administration (OSHA) guidelines regarding safety practices
Arithmetic to calculate amounts of materials needed and to measure materials to be laid out, cut, shaped, threaded, joined, etc.
Electrical principles and theories
The methods and techniques required in lifting, moving, stacking, storing, and protecting tools, equipment and materials
Plumbing systems and operations
Proper use and hazards of chemical materials (e.g. paints, wood primers, roof coatings, caustic acids, etc.)
Lighting fixtures including those for emergency egress routes
Ability to travel/work long rotations away from home
Stand for long periods of time (up to 12 hours or more) with scheduled breaks
Short and Long-distance walking required
Use of stairs and step stools
Use force when pushing/ pulling carts that weigh on average 50lbs
Must be able to crouch, bend neck, back and torso from waist to floor, and must be able to twist from left to right and right to left
Frequently lift an average weight of 25lbs with a maximum of 50lbs, on occasion where weights may exceed 50lbs the assistance of another person or a lifting aid is mandatory
Frequently reach below waist, waist to shoulder and above shoulder with frequent neck/back/torso twisting from left to right without restriction
Perform repetitive movements at the wrist including side to side/ up or down and multiple grasps of an average of 10lbs with a maximum of 25lbs
Simple, power and fine finger manipulation for a duration of an average 12-hour shift