989 Facility Maintenance jobs in Canton,MS

New, Posted 1 day ago

Apply Directly

Food Processing Maintenance Technician

BONDUELLE AMERICAS

Jackson, MS 39212

~ 35 min OnsiteBilingual Preferred

Must be able to rebuild gearboxes, power drives, and centrifugal pumps and replace mechanical shaft seals.
Must be able to install production equipment on elevated platforms.
Must be able to weld Stainless Steel. Weld quality to be acceptable for food grade applications.
Must be knowledgeable in liquid pumping principles and able to read pump flow curves.
Must be able to repair/rebuilt pneumatic hoists.
Must be able to time automated equipment drives using vendors manuals and specifications.
Must be knowledgeable in the operating principles of hydraulic systems and able to troubleshoot and repair their mechanical components.
Must be knowledgeable in the operating principles of pneumatic waste system and able to troubleshoot and repair mechanical components.
Must be knowledgeable in mechanical drive fundamentals, i.e. chain drive sprocket and gearbox ratios etc.
Must be able to read piping diagrams and identify the function of various components for air and water distribution systems.
Must be able to replace Slicer/cutter/dicer blade assemblies and perform the necessary adjustments.
Must be able to replace automated equipment mechanical components.
Must be proficient in the use of standard hand tools such as wrenches, hammers, bearing pullers etc.
Must be proficient in the use of simple power tools such as drills, grinders, cut-off saws, impact wrenches, etc.
Must be knowledgeable in cleaning and degreasing techniques.
Must be knowledgeable in basic plumbing repairs & installation
Must be knowledgeable in programming Variable Frequency Drives (VFD's).
Must be able to read electrical diagrams and identify individual components.
Must be able to run electrical conduit and be knowledgeable of code requirements.
Must be able to troubleshoot power distribution systems.
Must have working knowledge of electrical testing equipment such as multimeter, megger, etc.
Must be able to program simple production equipment such as metal detectors, spin dryers, etc.
Must be able to troubleshoot systems up to 480 volts with complicated electrical controls and wire 3 phase motors.
Must be knowledgeable in equipment safety requirements as they apply to equipment moving and installation.
Must be knowledgeable in Welding safety practices and Hot-work Permit requirements.
Must be knowledgeable in forklift and scissors lift safety.
Must have working knowledge in 480-volt electrical safety practices.
Must be able to safely operate shop equipment such as grinders, cut-off saws, power tools, ladders etc.
Must have working knowledge of basic protective equipment requirements as they apply to maintenance personnel.
Must be knowledgeable in the proper use of portable fire extinguishers.
Must be knowledgeable of safe lifting techniques.
Must have working knowledge of OSHA, FDA and GMP requirements as they pertain to maintenance activities at a food processing facility.
Must have working knowledge of basic Protective Equipment Requirements as they apply to maintenance personnel.
Must be knowledgeable in equipment Lock-Out/Tag-Out requirements. Must not by-pass Safety Devices under any circumstance!
Must be knowledgeable of safe lifting techniques, and expected to ask for help if item to move is too heavy.
Must use Slip-resistant footwear due to nature of environment: Wet floors, cold and probably some icing/debris.
Must use/wear/follow PPE, and GMP compliance as needed, including but not limited to: Hair/Bear net, Boots, Clean Smock, Waterproof Rubber Gloves, Plastic sleeves, Cut resistant gloves, eye & hearing protection, face shield, PPE to handle Chemicals when applicable, etc.
Must be aware of potential hazards as: Paper/knife cuts, Slip/falls due to wet floors, Pinch Points/Contusions, Chemical exposure (chlorine), Back/Arms/Legs sprains.
Able to read/write in English and communicate in Spanish.
Able to work flexible hours and overtime as required by workload.
Able to function in a team environment where continuous improvement is expected through communication and cooperation.
Must be willing and able to contribute to and implement department programs, procedures and systems as needed.
Must be able to qualify for forklift, and scissors lift drivers license.

SmartExplore AI is experimental.

Production and Warehouse Workers

Manpower Group

Jackson, MS 39203

Part Time Maintenance Technician - Jackson MS

Marsden Services

Jackson, MS 39216

~ 35 min Onsite

Must be able to work in a physically demanding environment. Frequent kneeling, lifting, pushing, pulling, bending and moving throughout the day.
Regular lifting of more than 20 lbs. and frequent lifting of up to 80 lbs. with assistance.
May encounter heights, ladders, uneven walking surface, stairs, confined spaces, dust, gas fumes from power equipment and noise.
Exposed to external weather conditions, drafts and interior temperature changes.
Will regularly handle supplies and tools with sharp edges.
Must be able to quickly and easily navigate the property/building as required to meet the job functions, including climbing stairs and walking the hallways and common areas.
High school graduate or equivalent.
2-year Technical Degree or equivalent work experience.
Four years multi-family or commercial building maintenance or equivalent experience.
Intermediate computer skills include the ability to send & receive emails, enter hours worked on internet-based system and access/perform data entry in Microsoft Office products including Microsoft Excel.
Must provide own hand tools: Hammer, Screwdriver (Phillips and Slotted), Crescent Wrench, Channellock Pliers, Pipe Wrench, Allen Wrench, Utility Knife, Flashlight, Hacksaw, Nut Drive Set, ¼” Socket Set, Set of Star Bits, Wire Stripper, Torpedo level, Inspection Mirror, Cordless drill, Tape Measure, GFI Receptacle Tester, Handheld Infrared/Laser Thermometer, Basic Multimeter.
Valid driver's license.
Access to reliable transportation.
Must be able to work on call; weekends as scheduled; must be available for overtime as needed.

SmartExplore AI is experimental.

New, Posted 6 hours ago

UPS - Warehouse Worker/Package Handler $21+/hr

UPS

Ridgeland, MS 39157

$21/hr

No Experience

Easy Apply

USA Warehouse Operator

Adecco

Clinton, MS 39056

$17.24/hr

~ 40 min OnsiteHealth InsurancePaid Time OffRetirement Benefit

High School Diploma/GED or equivalent experience required
Must be able to lift, push or pull at least 75 pounds
Ability to load and unload.
Material Handling Experience required Minimum of 3 years.
At least 1-year experience working in a high-volume distribution center or large retail operation.
2-3 years of direct operations experience.
Must be able to maintain forklift certification

SmartExplore AI is experimental.

New, Posted 6 hours ago