Home My Resume Saved Jobs Matches Feedback

974 Solutions Engineer jobs in Davenport,IA

New, Posted 14 hours ago

iHire

Quality Technician

Nestle

Davenport, IA 52801

Health InsuranceRetirement Benefit

Apply Directly

Controls Technician

Trane Technologies

Davenport, IA 52807

Onsite

Safety Sensitive Role: Yes
Must possess a valid driver's license for a minimum of 12 months, with no major or frequent traffic violations including, but not limited to: DUI, Hit & Run, License Suspension, Reckless / Careless Driving or multiple smaller infractions or preventable collisions in the previous 3 years
Must be able to reach your hands over your head
This role may be exposed to variable weather conditions, moving mechanical parts, heights, risk of electrical shock, noisy operating equipment and other variable environmental conditions based on location
Must be able to comfortably and routinely access rooftops with extension and/or fixed ladders at heights of 15' to 20', and occasionally, up to 50 feet +
Operating knowledge of Microsoft office software and working proficiency with hand held computer (i.e. Smartphone, iPad)
This position is highly physical and requires regular use of hands, fingers, walking, stooping, kneeling and climbing ladders. It requires employees to regularly lift and or move up to 10 lbs., frequently lift and/or move up to 40 lbs. and occasionally lift and/or move more than 40 lbs.
Must be able to twist the trunk of your body 90 degrees in each direction
A High School Diploma or equivalent
Must be able to squat and touch the floor with both hands
Annual Base Salary Range or Hourly Base Pay Range: $26.64 - $35.90
Compensation Type: Hourly
Typically at least 3-5 years of experience in HVAC/Controls
Must be able to maneuver confined access areas, as small as 30” vertical x 45” horizontal
Must be able to wear helmets, safety goggles, fall protection harness and safety boots to safely perform job duties
Must be able to stand on concrete surfaces for extended periods, routinely up to 4 hours
Must be able to safely and legally operate a vehicle using a seat belt
Must be able to safely use a ladder with a 375 lb. total weight limit, while carrying equipment of 50 lbs. or less

SmartExplore AI is experimental.

Apply Directly

Tech Support engineer

Net2Source (N2S)

East Moline, IL 61244

$23/hr

New, Posted 2 hours ago

Apply Directly

Assembly Technician - Wed-Sat

Eaton Aerospace

Davenport, IA 52801

$29.53/hr

OnsiteHealth InsuranceRetirement Benefit

This position requires use of information or access to hardware which is subject to the International Traffic in Arms Regulations (ITAR). All applicants must be U.S. persons within the meaning of ITAR
Must be able to lift up to 50 lbs. without assistance
Minimum of 2 years technical degree (electrical or electrical/mechanical) or mechanical degree
Eaton will not consider applicants for employment immigration sponsorship or support for this position
Active-Duty Military Service member candidates are exempt from the geographical area limitation
No relocation benefit is being offered for this position. Only candidates within 70 miles of Davenport, IA will be considered
ITAR defines a U.S. person as a U.S. Citizen, U.S. Permanent Resident (i.e. 'Green Card Holder'), Political Asylee, or Refugee

SmartExplore AI is experimental.

New, Posted 6 hours ago

Apply Directly

Project Engineer

Jobot

Andalusia, IL 61232

$180,000/yr

Flexible ScheduleRetirement Benefit

Apply Directly

Final Assembly Level 4

Dover Corporation

Rock Island, IL 61201

$23.40-$29.65/hr

~ 11 min OnsiteEducation AssistanceHealth InsurancePaid Time OffRetirement Benefit

Requires a high school diploma or its equivalent with experience in industrial manufacturing.
Ability to compute rate, ratio, and percent and to draw and interpret bar graphs.
Verbal and written communication sufficient to complete required paperwork
Ability to read, analyze, interpret general business periodicals, professional journals, technical procedures, or governmental regulations.
Visual quality check to verify all features are complete and meet visual requirements such as surface finish and free from blemishes
Ability to read and interpret manufacturing drawings and perform quality checks using measuring equipment such as Calipers, Micrometers, and CMM
Basic computer skills
Onsite work arrangement
Ability to effectively present information and respond to questions from groups of managers, clients, customers, and the public.
Verify measuring equipment calibration daily
Ability to write reports, business correspondence, and procedure manuals.
Ability to add, subtract, multiply, and divide in all units of measure, using whole numbers, common fractions, and decimals.

SmartExplore AI is experimental.

Apply Directly